- 您现在的位置：买卖IC网 > Sheet目录1313 > 2332B (Switchcraft Inc.)CONN JACK BLOCK DUAL
EN3 MINI WEATHERTIGHT CONNECTOR SERIES
42
CONNECTORS & RECEPTACLES
?
PHONE: 773 792-2700
* Please visit the product pages on our website for the most up-to-date product information
CRIMP CONTACT
CRIMP TOOLS
INSERTION INSTRUCTIONS
Part Number
EN3INS16
EN3INS20
EN3CR
EN3CRAUTO
EN3POS16
EN3POS20
Tool Description
Insertion/Extraction Tool for 16 AWG
Insertion/Extraction Tool for 20 AWG
Crimp Hand Tool
Pneumatic Crimp Tool
Positioner for 16 AWG contacts and pins
Positioner for 20 AWG contacts and pins
CRIMP CONTACT
EXTRACTION INSTRUCTIONS
NOTE: A positioner must be used with the
EN3CR and EN3CRAUTO.
Note: Solder and PC contacts are factory assembled
CORD CONNECTOR ASSEMBLY INSTRUCTIONS
STEP 1
Cord Connector: To assemble the three-part cord connector, first feed the end of the cable through the boot, cable clamp
housing, and coupling ring in that order and position as shown in the figure below. NOTE: The coupling ring can also be
inserted onto the cord connector from the front. In-line Connector: Feed the end of the cable through the boot and cable
clamp housing in the order and position shown.
IN-LINE
CABLE
BOOT
COUPLING
RING
CORD
CONNECTOR
CABLE
BOOT
CABLE CLAMP
HOUSING
CONNECTOR
CABLE CLAMP
HOUSING
CONTACT PINS
O-RING
(MOLDED ONTO
CONTACT PINS
CORD CONNECTOR)
STEP 2
Next, strip the cable .218" as shown and begin soldering conductors to pins, or insert contacts crimped on wire starting
with contact #1 next to the "notch" and following with the remaining conductors counter-clockwise with #6 or #8 conductor
in the center.
3/8"
MAX.
7/32"
SOLDER
NOTCH (PIN #1
INDICATOR)
CORD
CONNECTOR
9/32"
3/8"
MAX.
7/32"
SOLDER
NOTCH (PIN #1
INDICATOR)
IN-LINE
CONNECTOR
9/32"
STEP 3
Push the cable clamp housing forward until it locks
into the connector body and snap the two clamps
into their compartments.
CORD CONNECTOR
CABLE CLAMPS
IN-LINE CONNECTOR
CABLE CLAMPS
STEP 4
CORD CONNECTOR
IN-LINE CONNECTOR
Finally, push the boot all the way forward to seat tightly
onto the cable clamp housing.
Remember: Cord connectors will not mate with each other. For cord-to-cord connection,
your customer must order a cord connector plus an in-line connector.
DIMENSIONS ARE FOR REFERENCE ONLY
Inch
(mm)
www.switchcraft.com
? Registered trademark of Switchcraft, Inc.
Note: Contact your Switchcraft Representative for price and delivery
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
236PKG
CONN PLUG AUDIO PHONE R/A 3 COND
238
CONN PLUG FLAT 3COND SOLDER LUG
242102
CONN ADT SMA PLUG-BNC JACK
242103
CONN ADT SMA JACK-BNC PLUG
242105RP
CONN ADT SMA JACK-TNC R/P PLUG
242107RP
CONN ADT SMA JACK-TNC R/P JACK
242112RP
CONN ADT SMA R/P PLUG-N JACK
242113RP
CONN ADT R/P SMA JACK-N PLUG
相关代理商/技术参数
2332BG
制造商:Aavid Thermalloy 功能描述:35683 制造商:Aavid Thermalloy 功能描述:- Bulk 制造商:Aavid Thermalloy 功能描述:Aavid Internal P/N:035683
2332B-TACHG
功能描述:散热片 41.3X43.2X16.5 BGA BLACK ANODIZE RoHS:否 制造商:Ampro By ADLINK 产品:Heat Sink Accessories 安装风格:Through Hole 散热片材料: 散热片样式: 热阻: 长度: 宽度: 高度: 设计目的:Express-HRR
2332BX
功能描述:电话连接器 DUAL JACK BLOCK RoHS RoHS:否 制造商:Switchcraft 标准:1/4 in 开关配置:Switched 型式:Female 位置/触点数量: 端接类型:Solder 安装风格:Chassis (Panel) 方向:
2332-CLC
制造商:Platt Luggage 功能描述:
2332D5
功能描述:面板安装指示灯 GREEN DIFFUSED
RoHS:否 制造商:Chicago Miniature 产品:Oil-Tight Non-Relampable Neon LED Indicators 灯类型:Neon 灯座类型:Wire Terminal 工作电压:105 VAC to 125 VAC 封装:Bulk
2332DX5
功能描述:面板安装指示灯 RECT PMI W/TERM BK BZL
RoHS:否 制造商:Chicago Miniature 产品:Oil-Tight Non-Relampable Neon LED Indicators 灯类型:Neon 灯座类型:Wire Terminal 工作电压:105 VAC to 125 VAC 封装:Bulk
2332-L
制造商:Milwaukee Electric Tool Corporation 功能描述:M12 REALTREE AP HEATED JACKET LARGE 制造商:MILWAUKEE TOOL 功能描述:M12 REALTREE AP HEATED JACKET LARGE
2332NM
制造商:Thomas & Betts 功能描述: